AOTC Tusken Raider WIP
Moderator: DCO
-
tenebris
- Base Membership Officer, Detachment CO
- Posts: 1233
- Joined: Wed Jan 03, 2018 1:34 pm
- Name: empathy gray
- 2020 Troops:: 0
- Total Troops: 6
- 501st Number: 70969
- MMCC Name:: Tenebris
Re: AOTC Tusken Raider WIP
Just to let you know I've seen this (but today is my respite day)I'll have a look at the refs and tutorial later. from a quick look it looks like there's no band on the cross over and a mandarin collar....But I think you are on the right track.
-
SirCalcium
- Posts: 200
- Joined: Wed Jan 03, 2018 11:47 am
- Name: Calum Macqueen
- Location: Kilmarnock
- 2020 Troops:: 4
- Total Troops: 59
- MMCC Name:: Cal Starkno
Re: AOTC Tusken Raider WIP
Amendments, on the tutorial there is a gap cut out in the middle that's 25 x 4 inches, that where the lower half will attach to the torso half
when worn with a sash or belt the sleeves bunch up making it look more like the tusken robes
For the taper, I'm thinking I'll start at the 24 inches, but narrow down to 20 inches close to the gap
Red Line
As for the opening, I've redrawn the line where I personally think that should go
Outside Red Line
when worn with a sash or belt the sleeves bunch up making it look more like the tusken robes
For the taper, I'm thinking I'll start at the 24 inches, but narrow down to 20 inches close to the gap
Red Line
As for the opening, I've redrawn the line where I personally think that should go
Outside Red Line
But you must accept your regret the way you accept your mistakes. Then move on.
-
SirCalcium
- Posts: 200
- Joined: Wed Jan 03, 2018 11:47 am
- Name: Calum Macqueen
- Location: Kilmarnock
- 2020 Troops:: 4
- Total Troops: 59
- MMCC Name:: Cal Starkno
Re: AOTC Tusken Raider WIP
Quick update, I tapered the sleeves, and I think it looks better with
And I added the mask and arms onto this mock up for reference
And I added the mask and arms onto this mock up for reference
But you must accept your regret the way you accept your mistakes. Then move on.
-
SirCalcium
- Posts: 200
- Joined: Wed Jan 03, 2018 11:47 am
- Name: Calum Macqueen
- Location: Kilmarnock
- 2020 Troops:: 4
- Total Troops: 59
- MMCC Name:: Cal Starkno
Re: AOTC Tusken Raider WIP
The sleeves were bothering me as I felt the cuffs were too wide, browsing on the main RL forum and saw mention that the sleeves taper towards the waist, so I've done test, I wrapped a scrap bit of fabric around my waist for reference.
Right arm, altered. Left arm, Unaltered
Right arm, altered. Left arm, Unaltered
But you must accept your regret the way you accept your mistakes. Then move on.
-
SirCalcium
- Posts: 200
- Joined: Wed Jan 03, 2018 11:47 am
- Name: Calum Macqueen
- Location: Kilmarnock
- 2020 Troops:: 4
- Total Troops: 59
- MMCC Name:: Cal Starkno
Re: AOTC Tusken Raider WIP
Began work on my Gaffi Stick, using the Gunstock design. Legion Judge on the main forum said PT Tuskens are allowed to use them.
The mace head was 3D printed by Richard Tonge aka Gunnerbill Sent from my ONEPLUS A6013 using Tapatalk
The mace head was 3D printed by Richard Tonge aka Gunnerbill Sent from my ONEPLUS A6013 using Tapatalk
You do not have the required permissions to view the files attached to this post.
But you must accept your regret the way you accept your mistakes. Then move on.
-
SirCalcium
- Posts: 200
- Joined: Wed Jan 03, 2018 11:47 am
- Name: Calum Macqueen
- Location: Kilmarnock
- 2020 Troops:: 4
- Total Troops: 59
- MMCC Name:: Cal Starkno
Re: AOTC Tusken Raider WIP
In my attempt at dyeing the fabric, one came out a different hue than the other. So I may have to abandon this method and find some natural stuff, unless there's a way to darker shade lighter again
Sent from my ONEPLUS A6013 using Tapatalk
You do not have the required permissions to view the files attached to this post.
But you must accept your regret the way you accept your mistakes. Then move on.